This instrument is a unique, which not only measure the Human being Static voltage but also drains safely to the ground, without giving any shocks to the persons.
1). The Human body voltage meter, must always be grounded, to give an accurate results
and also this helps in draining the Human body voltage safely to the ground.
2). Gently touch the “TOUCH TO TEST” plate to test the body voltage.
3).The reading displays the peak voltage generated by the Human being at that instant and
slowly the voltage drops down, because of the grounding, of the Human being. through
the meter.
4). Human being should touch the plate, until the reading shown is less than 100 volts, indicating
almost all the static voltage which is accumulated in his body is drained and he is static safe.
5). The range of the meter is 0-1999 volts and at 100 volts and above an audio, visual alarm is
also provided. When ever Human being touches the meter.
6). The instrument is very sensitive and even a smallest voltage present in air, (running fan) is
also seen.
7). The meter in on condition will show any reading from 000-003 volts (Indicating some
charges are present in the atmosphere).
8). This reading of 000-003 does not effect the actual reading, once touched by the Human being to
the plate for his body static voltage in volts. Specifications :Indicating Range : +/- 1999V
Display : 3 ½ Digit LCD Display,
Resolution : 1 Volt,
Accuracy : 10%
Test Surface : S.S.Plate,
Power Supply : 9V Battery
Calibration : Recommended once in 12 months
Warranty : 12 months,
Indication : At 100 Volts indicate through Red light and
gives a buzzer sound
The Static Alarm senses changes in electrostatic fields. The static alarm is ideal for scanning the electrostatic field in critical areas of production and testing of electronic circuit, plastic and textile industries. Specifications : Detection method : Charge coupling by field Interception
Detection sensitivity : +/- > 100V
Range selection : Auto ranging and auto resetting
Indication : Prominent for LED visual indication with audible alarm ,
Power Supply : 9V Battery
The model WSM – 01 has independent circuitry designed to continuously monitor the connections to ESD earth of Wrist strap & Work surface.
Wrist Strap : This section continuously monitors the wrist strap to detect loss of continuity between operator and monitor. Conditions such as broken coils cords and improper contact with the skin are detected instantly to alert the operator
before serious and expensive ESD damage can occur. As there is no resistance return path from the wrist strap, it uses the ‘capacitive AC pulse principle’ to check if the operator is adequately grounded. The wrist strap section is automatically activated when it is plugged in. Continuous monitoring reduces the need for periodic checks and also ensures greater security.
ESD Work Surface : The work surface is monitored by a DC Resistive principle and a warning is given in case the surface to ground resistance exceeds the safe threshold value of 10 Meg Ohms. Specifications : Pass Threshold : Under 4 Meg ohms for Wrist Strap
Under 10 Meg ohms for Mat
Indication :
Green LED Wrist Strap : Pass
Red LED Wrist Strap : Fail,
Red LED Mat : Fail
Audible alarm : Flashing Red LED for Wrist Strap
Steady Red LED for Mat
Input Power : 12 V 500 ma DC,
Accuracy : +/- 10%
Repeatability : +/- 10%,
Dimensions : 125 x 65 x 35 mm
Warranty : 12 Months,
Optional : 12 V Adopter
The model WSM – 02 has independent circuitry designed to continuously monitor the connections to ESD earth of Two Wrist strap section & Work surface. Wrist Strap : Two – Wrist strap section continuously monitors the wrist strap to detect loss of continuity between operators and monitor. Conditions such as broken coils cords and improper contact with the skin are detected instantly to alert the operator before serious and expensive ESD damage
can occur. As there is no resistance return path from the wrist strap, it uses the ‘capacitive AC pulse principle’ to check if the operator is adequately connected to the instrument. The wrist strap sections are automatically activated when it is plugged in. Continuous monitoring reduces the need for periodic checks and also ensures greater security. ESD Work Surface : The work surface is monitored by a DC Resistive principle and a warning is given in case the surface to ground resistance exceeds the safe threshold value of 10 Meg Ohms.
Parts Supplied with continuous work station monitor
1). Fixing Clamp,
2). 18 V DC Adopter (Optional)
3). Warranty certificate, Specifications : 1). Pass Threshold : Under 4 Meg ohms for Wrist Strap
Under 10 Meg ohms for Mat
2). Indication :
Green LED Wrist Strap : Pass
Red LED Wrist Strap : Fail
Red LED Mat : Fail,
Audible alarm : Flashing Red LED for Wrist Strap
Steady Red LED for Mat
3). Input Power : 18 V 500 ma DC,
4). Accuracy : +/- 10%
5). Repeatability : +/- 10%,
6). Dimensions : 130 x 90 x 30 mm
7). Warranty : 12 Months,
8). Calibration : Recommended every 12 Months
Air ions are molecules that have lost or gained an electron. Ions are present in normal air but are “stripped” out when an air is subject to filtration and conditioning. They are produced by radioactive emission or by phenomenon called “corona discharge” where a high voltage is applied to sharp point.
All air ionization systems work by flooring the atmosphere with positive and negative ion, when ionized air comes in contact with a charge surface; the charge surface attracts ions of the opposite polarity. As a result the static electricity that has built up on products, equipment and surface is neutralized.
Typically, air is very insulative with a resistive exceeding 10^15 Ohms / Meter. By increasing the numbers of ions in the air it is possible to lower the resistivity of the air to 10^11 Ohms / meter, there by making the air more conductive. Conductive air can neutralize the static charge on every surface that it contents. The filed from the charged surface attracts ions of the opposite polarity until the charged on the surface is neutralized.
The Over Head Ionizer is portable and uses a four fan to produce airflow. High voltages generated out of the supply line voltage are applied to stainless steel ion emitter points. These points produce intense alternating polarities, ionizing the air instantly in the fan airflow.
The Over Head Ionizer is designed for use when handling sensitive electronic components where electrostatic discharge is a problem. The unit can also used where static electricity causes problems such as; attraction of drift to product, misalignment of small parts due to electrostatic “jumping” and undesirable adhesion of plastic films due to electrostatic charge. Specifications : Air flow : 90 CFM
Noise Level : 43 dBA,
Power Supply : 210 V – 250 V AC / 50 Hz
Ionization Voltage : +/- 6 KV,
Un Balance Voltage : < +/- 50 KV
Construction : Power coated MS Cabinet
Warranty: 12 Months
Smoke Absorber is a portable Smoke Extractor incorporating state-of-the-art technology.
A power fan in the unit, draws the fume onto a special activated carbon filter, the fact that soldering fumes carry a positive charge is taken advantage of in the design. The filter is given a negative electrostatic charge to improve the efficiency and fume trapping ability. Specifications :
Power Source : 230 V AC,
Power Consumption : 20 Watts
Fan : Sealed ball – bearing brush less motor,
Air Volume : 1.8 cu m / min
Filter element : Replaceable activated – carbon foam
Filter size : 150 x 200 x 230 mm,
Warranty : 12 Months
Air ions are molecules that have lost or gained an electron. Ions are present in normal air but are “stripped” out when an air is subject to filtration and conditioning. They are produced by radioactive emission or by phenomenon called “corona discharge” where a high voltage is applied to sharp point.
All air ionization systems work by flooring the atmosphere with positive and negative ion, when ionized air comes in contact with a charge surface; the charge surface attracts ions of the opposite polarity. As a result the static electricity that has build up on products, equipment and surface is neutralized.
Typically air is very insulative with a resistive exceeding 10^15 Ohsm / meter. By increasing the numbers of ions in the air it is possible to lower the resistivity of the air to 10^11 ohms / meter, there by making the air more conductive. Conductive air can neutralize the static charge on every surface that it contents. The field from the charged surface attracts ions of the opposite polarity until the charged on the surface is neutralized.
The Static Neutralizer is portable and uses a small fan to produce airflow. High voltages generated out of the supply line voltage are applied to stainless steel ion emitter points. These points produce intense alternating polarities, ionizing the air instantly in the fan airflow.
The Static Neutralizer is designed for use when handling sensitive electronic components where electrostatic discharge is a problem. The unit can also used where static electricity cause problems such as; attraction of drift to product, misalignment of small parts due to electrostatic “jumping” and undesirable adhesion of plastic films due to electrostatic charge. Specifications :
Air flow : 1.8 cu m / min
Noise Level : 45 dba (at 1 m),
Power Supply : 210 V – 250 V AC / 50 Hz
Ionization Voltage : +/- 6 KV,
Un Balance Voltage : < +/- 100 KV
Construction : Power coated MS Cabine,
Warranty : 12 Months
